Diese Website verwendet Cookies. Durch die Nutzung dieser Website stimmen Sie der Verwendung von Cookies zu. Weitere Informationen finden Sie in unseren Datenschutzrichtlinie.

Die Bilder dienen nur als Referenz,

Siehe Technische Spezifikationen

ATSAMB11-MR210CA +BOM

This module is designed for seamless Bluetooth communication, supporting 802.15.1 standards for reliable wireless connections

Hersteller:

Microchip Technology
Herstellerteil #:

ATSAMB11-MR210CA
Datenblatt:

ATSAMB11-MR210CA Datenblatt (PDF)
Series:

SmartConnect
Programmabe:

Not Verified
RF Family/Standard:

Bluetooth
Protocol:

Bluetooth v4.1
EDA/CAD Modelle:

Fordern Sie kostenlose CAD-Modelle für an ATSAMB11-MR210CA

ATSAMB11-MR210CA Allgemeine Beschreibung

Catering to the needs of battery-powered devices, the ATSAMB11-MR210CA boasts impressive energy efficiency, ensuring prolonged operational performance. Thanks to its ARM Cortex-M0 processor, the module delivers robust processing power for seamless application execution and efficient communication handling. Moreover, its support for various Bluetooth profiles and protocols guarantees compatibility with a wide spectrum of devices and systems, further enhancing its versatility. With built-in security measures, this module prioritizes data integrity and secure communications, catering to the stringent security requirements of modern applications

Hauptmerkmale

Core
– ARM® Cortex®-M3 revision 2.0 running at up to 64 MHz
– Memory Protection Unit (MPU)
– Thumb®-2 instruction set
Pin-to-pin compatible with AT91SAM7S series (48- and 64-pin versions)
Memories
– From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator, single plane
– From 16 to 48 Kbytes embedded SRAM
– 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines
– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support
– Memory Protection Unit (MPU)
System
– Embedded voltage regulator for single supply operation
– Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation
– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low power 32.768 kHz for RTC or device clock
– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. Inapplication trimming access for frequency adjustment
– Slow Clock Internal RC oscillator as permanent low-power mode device clock
– Two PLLs up to 130 MHz for device clock and for USB
– Temperature Sensor
– Up to 22 peripheral DMA (PDC) channels
Low Power Modes
– Sleep and Backup modes, down to 1.8 µA in Backup mode
– Ultra low power RTC
Peripherals
– USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip Transceiver
– Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and Modem Mode
– Two 2-wire UARTs
– Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller (I2S), 1 High Speed Multimedia Card Interface (SDIO/SD Card/MMC)
– Up to 6 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM mode. Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper Motor
– 4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control
– 32-bit Real-time Timer and RTC with calendar and alarm features
– Up to 15-channel, 1Msps ADC with differential input mode and programmable gain stage
– One 2-channel 12-bit 1Msps DAC
– One Analog Comparator with flexible input selection, Selectable input hysteresis
– 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)
– Write Protected Registers
– Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination
– Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel Capture Mode
Packages
– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm
– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm
– 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5 mm

Spezifikationen

Series	SmartConnect	Programmabe	Not Verified
RF Family/Standard	Bluetooth	Protocol	Bluetooth v4.1
Frequency	2.4GHz	Power - Output	4dBm
Sensitivity	-96dBm	Serial Interfaces	I2C, SPI, UART
Antenna Type	Integrated, Chip	Memory Size	256kB Flash, 128kB ROM, 128kB RAM
Voltage - Supply	2.3V ~ 3.6V	Current - Receiving	4mA
Current - Transmitting	3mA	Mounting Type	Surface Mount
Base Product Number	ATSAMB11

Servicerichtlinien und andere

After-Sales- und Abwicklungsbezogen

Zahlung

Bezahlverfahren

TT/Überweisung

Paypal

Western Union

Geldgramm

Für alternative Zahlungskanäle kontaktieren Sie uns bitte unter:

[email protected]

Versand & Verpackung

Versandart

Fedex

UPS

DHL

NTN

Verpackung

AVAQ bestimmt und verpackt alle Geräte auf der Grundlage der Schutzanforderungen gegen elektrostatische Entladung (ESD) und Feuchtigkeitsempfindlichkeit (MSL)..