Diese Website verwendet Cookies. Durch die Nutzung dieser Website stimmen Sie der Verwendung von Cookies zu. Weitere Informationen finden Sie in unseren Datenschutzrichtlinie.

Die Bilder dienen nur als Referenz,

Siehe Technische Spezifikationen

TDA8007BHLBE +BOM

Smart Card Interface 10MHz 3.3V/5V 700mW 48-Pin LQFP

Hersteller:

NXP Semiconductor
Herstellerteil #:

TDA8007BHLBE
Datenblatt:

TDA8007BHLBE Datenblatt (PDF)
Interface:

Parallel
Voltage - Supply:

2.7V ~ 6V
Mounting Type:

Surface Mount
Base Product Number:

TDA800
EDA/CAD Modelle:

Fordern Sie kostenlose CAD-Modelle für an TDA8007BHLBE

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

TDA8007BHLBE Allgemeine Beschreibung

The TDA8007BHL is a cost-effective card interface for dual smart card readers. Controlled through a parallel bus, it meets all requirements of ISO 7816, GSM 11-11, EMV4.2 and EMV 2000. It is addressed on a non-multiplexed 8-bit databus, by means of address registers AD0, AD1, AD2 and AD3. TDA8007BHL/C3 can be also addressed through a multiplexed access. The integrated ISO UART and the time-out counters allow easy use even at high baud rates with no real time constraints. Due to its chip select, external input/output and interrupt features, it greatly simplifies the realization of a reader of any number of cards. It gives the cards and the reader a very high level of security, due to its special hardware against ESD, short-circuiting, power failure, etc. The integrated step-up converter allows operation within a supply voltage range of 2.7 V to 6 V.

TDA8007BHL/C4 supports only non multiplex access and TDA8007BHL/C3 support both non multiplexed and multiplexed access.

Hauptmerkmale

Control and communication through an 8-bit parallel interface, compatible with non-multiplexed memory access, TDA8007BHL/C3 can be also addressed through a multiplexed memory access
Specific ISO UART with parallel access input/output for automatic convention processing, variable baud rate through frequency or division ratio programming, error management at character level for T = 0 and extra guard time register
FIFO for 1 to 8 characters in reception mode
Parity error counter in reception mode and in transmission mode with automatic re-transmission
Dual VCC generation: 5 V ± 5 %, 65 mA (max.); 3 V ± 8 %, 50 mA (max.) or 1.8 V ± 10 %, 30 mA (max.); with controlled rise and fall times
Dual cards clock generation (up to 10 MHz), with three times synchronous frequency doubling (fXTAL, 1/2fXTAL, 1/4fXTAL and 1/8fXTAL)
Cards clock stop (at high or low level) or 1.25 MHz (from internal oscillator) for cards Power-down mode
Automatic activation and deactivation sequence through an independent sequencer
Supports the asynchronous protocols T = 0 and T = 1 in accordance with: ISO 7816 and EMV4.2
Versatile 24-bit time-out counter for Answer To Reset (ATR) and waiting times processing
Specific Elementary Time Unit (ETU) counter for Block Guard Time (BGT): 22 in T = 1 and 16 in T = 0
Minimum delay between two characters in reception mode:
in Protocol T = 0: 11.8 ETU
in Protocol T = 1: 10.8 ETU
Supports synchronous cards
Current limitations in the event of short-circuit (pins I/O1, I/O2, VCC1, VCC2, RST1 and RST2)
Special circuitry for killing spikes during power-on/power-off
Supply supervisor for power-on/power-off reset
Step-up converter (supply voltage from 2.7 V to 6 V), doubler, tripler or follower according to VCC and VDD
Additional input/output pin allowing use of the ISO UART for another analog interface (pin I/OAUX)
Additional interrupt pin allowing detection of level toggling on an external signal (pin INTAUX)
Fast and efficient swapping between the three cards due to separate buffering of parameters for each card
Chip select input allowing use of several devices in parallel and memory space paging
Enhanced ESD protections on card side (except C4x, C8x): 6 kV (min.)
Software library for easy integration within the application
Power-down mode for reducing current consumption when no activity.
Target Applications
Multiple smart card readers for multiprocessor applications (EMV banking, digital payTV and access control, etc.).

Spezifikationen

Category	Integrated Circuits (ICs)InterfaceSpecialized	Series	-
Applications	-	Interface	Parallel
Voltage - Supply	2.7V ~ 6V	Mounting Type	Surface Mount
Base Product Number	TDA800

Servicerichtlinien und andere

After-Sales- und Abwicklungsbezogen

Zahlung

Bezahlverfahren

TT/Überweisung

Paypal

Western Union

Geldgramm

Für alternative Zahlungskanäle kontaktieren Sie uns bitte unter:

[email protected]

Versand & Verpackung

Versandart

Fedex

UPS

DHL

NTN

Verpackung

AVAQ bestimmt und verpackt alle Geräte auf der Grundlage der Schutzanforderungen gegen elektrostatische Entladung (ESD) und Feuchtigkeitsempfindlichkeit (MSL)..