Diese Website verwendet Cookies. Durch die Nutzung dieser Website stimmen Sie der Verwendung von Cookies zu. Weitere Informationen finden Sie in unseren Datenschutzrichtlinie.

Die Bilder dienen nur als Referenz,

Siehe Technische Spezifikationen

TMAG5273A2QDBVT +BOM

Hall Effect Sensor X, Y, Z Axis SOT-23-6

Hersteller:

Texas Instruments
Herstellerteil #:

TMAG5273A2QDBVT
Datenblatt:

TMAG5273A2QDBVT Datenblatt (PDF)
Type:

3D Hall-Effect Sensor
Operating Supply Current:

3 mA
Maximum Output Current:

2 mA
Operating Point Min/Max:

133 mT to 266 mT
EDA/CAD Modelle:

Fordern Sie kostenlose CAD-Modelle für an TMAG5273A2QDBVT

TMAG5273A2QDBVT Allgemeine Beschreibung

The TMAG5273 is a low-power linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. This device integrates three independent Hall-effect sensors in the X, Y, and Z axes. A precision analog signal-chain along with an integrated 12-bit ADC digitizes the measured analog magnetic field values. The I²C interface, while supporting multiple operating V_CC ranges, ensures seamless data communication with low-voltage microcontrollers. The device has an integrated temperature sensor available for multiple system functions, such as thermal budget check or temperature compensation calculation for a given magnetic field.

The TMAG5273 can be configured through the I²C interface to enable any combination of magnetic axes and temperature measurements. Additionally, the device can be configured to various power options (including wake-up and sleep mode) allowing designers to optimize system power consumption based on their system-level needs. Multiple sensor conversion schemes and I²C read frames help optimize throughput and accuracy. A dedicated INT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion.

An integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.

The TMAG5273 is offered in four different factory-programmed I²C addresses. The device also supports additional I²C addresses through the modification of a user-configurable I²C address register. Each orderable part can be configured to select one of two magnetic field ranges that suits the magnet strength and component placement during system calibration.

The device performs consistently across a wide ambient temperature range of –40°C to +125°C.

Hauptmerkmale

Configurable power modes including:
- 2.3-mA active mode current
- 1-µA wake-up and sleep mode current
- 5-nA sleep mode current
Selectable linear magnetic range at X, Y, or Z axis:
- TMAG5273x1: ±40 mT, ±80 mT
- TMAG5273x2: ±133 mT, ±266 mT
Interrupt signal from user-defined magnetic and temperature threshold cross
5% (typical) sensitivity drift
Integrated angle CORDIC calculation with gain and offset adjustment
20-kSPS single axis conversion rate
Configurable averaging up to 32x for noise reduction
Conversion trigger by I²C or dedicated INT pin
Optimized I²C interface with cyclic redundancy check (CRC):
- Maximum 1-MHz I²C clock speed
- Special I²C frame reads for improved throughput
- Factory-programmed and user-configurable I²C addresses
Integrated temperature compensation for multiple magnet types
Built-in temperature sensor
1.7-V to 3.6-V supply voltage V_CC range
Operating temperature range: –40℃ to +125℃

Spezifikationen

Product Category	Board Mount Hall Effect / Magnetic Sensors	Type	3D Hall-Effect Sensor
Operating Supply Current	3 mA	Maximum Output Current	2 mA
Operating Point Min/Max	133 mT to 266 mT	Release Point Min/Max (Brp)	-
Operating Supply Voltage	1.7 V to 3.6 V	Minimum Operating Temperature	- 40 C
Maximum Operating Temperature	+ 125 C	Mounting Style	PCB Mount
Series	TMAG5273	Moisture Sensitive	Yes
Output Voltage	5.5 V	Product	Linear Hall Effect Sensors
Product Type	Hall Effect / Magnetic Sensors	Sensitivity	820 LSB/mT
Factory Pack Quantity	250	Subcategory	Sensors
Supply Voltage - Max	3.6 V	Supply Voltage - Min	1.7 V
Termination Style	SMD/SMT

Servicerichtlinien und andere

After-Sales- und Abwicklungsbezogen

Zahlung

Bezahlverfahren

TT/Überweisung

Paypal

Western Union

Geldgramm

Für alternative Zahlungskanäle kontaktieren Sie uns bitte unter:

[email protected]

Versand & Verpackung

Versandart

Fedex

UPS

DHL

NTN

Verpackung

AVAQ bestimmt und verpackt alle Geräte auf der Grundlage der Schutzanforderungen gegen elektrostatische Entladung (ESD) und Feuchtigkeitsempfindlichkeit (MSL)..